Next Return

Petzl Shunt

Version A Version B Version C
Version A Version B Version C
 
Version D Version E Version F
Version D Version E Version F

Overview


Version A
(#99, 2271)

Front Rear
Front Rear
 
Left Right Open for Rigging
Left Right Open for Rigging

Technical Details

I acquired my Petzl Shunt, Version A from Pathfinder Sports in 1979. I acquired three more in 2017 as part of Bob Thrun's collection.

Version A is 110 mm. tall, 64 mm. wide, and 76 mm. thick, and weighs 152 g. The shunt uses a stamped aluminum frame that wraps around one or two ropes. A forged aluminum lever is mounted in the center of the frame, and can be pulled through the back of the frame to allow rigging the rope. The lever is spring loaded so it will automatically return to the operating position. A 10 mm. round pin passes through the lever. In use, it presses the rope into a slight detent in the frame. There is a small hole in the back of the lever that one can attach a small cord to to allow remotely releasing the device. Aluminum blocks on each side of the frame provide some support for the frame and the bolt that serves as an axle for the lever.

The right side of the lever has "F. PETZL" in raised letters, and the left side has "SHUNT."

Comments

The Petzl Shunt is truly a unique ascender. It and its copies are the only type 2 lever cam ascenders in my collection.

The shunt can be used on double rope (but only if both ropes are the same size), and with care on single rope, although single rope use puts an asymmetrical torque on the lever. For some curious reason, the Petzl literature recommends ascending with only one ascender (attached to the seat harness), and wrapping the rope around the foot as a substitute for a second ascender. In an emergency this works, but I hardly think is the safest possibility. The shunt can be released under load by pulling down on the shell. This is easily done, and with only one ascender, one could easily get into trouble.

Petzl also recommends using a shunt as a rappel safety on double rope. I don't believe in rappel safeties for a number of reasons, so I can't recommend this either.

Petzl also suggested using the shunt for top rope belays, but I recommend using a good belay device instead.


Version B
(#2314)

Front Rear
Front Rear
 
Left Right Open for Rigging
Left Right Open for Rigging

Technical Details

I acquired my Petzl Shunt, Version B from Bob Elron at the 2017 NSS Convention. CarolJo Rushin-Elron originally obtained it from Bob & Bob in 1984, but doesn' remember ever using it.

Version B is 109 mm. tall, 64 mm. wide, 77 mm. thick, and weighs 154 g. The shunt uses a stamped aluminum frame that wraps around one or two ropes. A forged aluminum lever is mounted in the center of the frame, and can be pulled through the back of the frame to allow rigging the rope. The lever is spring loaded so it will automatically return to the operating position. A 10 mm. round pin passes through the lever. In use, it presses the rope into a slight detent in the frame. There is a small hole in the back of the lever that one can attach a small cord to to allow remotely releasing the device. Aluminum blocks on each side of the frame provide some support for the frame and the bolt that serves as an axle for the lever.

The right side of the lever has "F. PETZL" in raised letters, and the left side has "SHUNT."

Comments

Version B is anodized blue; otherwise, it is essentially the same as Version A.


Version C
(#100)

Front Rear
Front Rear
 
Left Right Open for Rigging
Left Right Open for Rigging

Technical Details

I acquired my Petzl Shunt, Version C from John E. Weinel, Inc. in 1989.

Version C is 110 mm. tall, 56 mm. wide, and 78 mm. thick, and weighs 189 g.

The right side of the shell has a stamped Sieg Heil icon. The right side of the lever has "PETZL" in raised letters, and the left side has "SHUNT." The bolt heads have "PETZL" and "8.8" in recessed characters.

Comments

Version C differs from Version A in several small details. The frame is now finished with Petzl's ugly "bird droppings" (a.k.a. "spew-vomit") finish. The lever is a somewhat cruder forging with a few differences in detail. The side pieces are now stamped from steel, and they wrap around the frame, giving it more support. The bolts are now hex-head, and may be slightly larger, but I'd have to disassemble mine to find out for sure.


Version D
(#1915)

Front Top
Front Top
 
Left Right Open for Rigging
Left Right Open for Rigging

Technical Details

I acquired my Petzl Shunt, Version D in 2012. I wrote the date September 2, 2012 on the box (indicating that I got it at the Old Timers Reunion), but I failed to record who I got it from.

Version D is 109 mm. tall, 55 mm. wide, 78 mm. thick, and weighs 189 g.

The right side of the shell has a stamped Sieg Heil icon. The right side of the lever has a raised Petzl logo, and the left side has "SHUNT" in raised letters. The bolt heads have "PETZL," "A2" and "80" in raised characters.

Comments

Version D has different style lever than Version C. The markings are also different; e.g., "SHUNT" reads bottom to top instead of top to bottom.


Version E
(#1527, 2069)

Front Rear
Front Rear
 
Left Right Open for Rigging
Left Right Open for Rigging

Technical Details

I acquired my Petzl Shunt, Version E from On Rope 1 in 2009. I acquired another in 2017 as part of Bob Thrun's collection.

Version E is 112 mm. tall, 55 mm. wide, 79 mm. thick, and weighs 175 g.

The left side of the shell is stamped with a Sieg Heil icon and "WARNING DANGER PROPER TRAINING IS ESSENTIAL FOR USE." The rear is stamped with the Petzl Logo and "06024KC." The right side is stamped with "DOUBLE ROPE 8≤Ø≤11," "SINGLE ROPE 10≤Ø≤11," a Reading-Is-Dangerous icon, and "CE0197." The right side of the lever has a raised Petzl logo, and the left side has "SHUNT" in raised letters. The bolt heads have "PETZL," "A2" and "80" in raised characters.

Comments

Version E has a different style lever than Versions C or D.


Version F
(#2338)

Front Rear
Front Rear
 
Left Right Open for Rigging
Left Right Open for Rigging

Technical Details

I acquired my Petzl Shunt, Version F from Expé-Spelemat in 2017.

Version F is 108 mm. tall, 55 mm. wide, 78 mm. thick, and weighs 174 g.

The left side of the shell is stamped with "SHUNT" and a hollow up-pointing arrow with "UP" inside. The right side is stamed with "ROPE ¤⇒" pointing to a book-with-an-"i" icon, a two-rope rigging illustration with "8≤Ø≤11" underneath, a one-rope rigging illustration with "10≤Ø≤11" underneath, and "CE 0082." The rear is stamped with the Petzl Logo and printed with "17E0081798147" and a scanner code. The right side of the lever has a raised Petzl logo, and the left side has "SHUNT" in raised letters. The bolt heads have "PETZL," "A2" and "80" in raised characters.

Comments

Petzl eliminated the ugly "bird droppings" (a.k.a. "spew-vomit") finish and returned to the traditional look of Version A. Mechanically, this version is identical to Version E.